A Beginner's Guide to Plumbing for Bathtub Installation
A Beginner's Guide to Plumbing for Bathtub Installation
Blog Article
The content in the next paragraphs pertaining to A Step-by-Step Guide to Installing a Bathtub is particularly stimulating. You should see for yourself.
Installing a bathtub isn't exactly brain surgery, however it does require strong plumbing, carpentry, as well as occasionally, tiling skills. Replacing an old bath tub with a brand-new one is additionally a reasonably difficult job. If the old tub is readily easily accessible, the job can relocate easily; if you need to open up a wall surface to get rid of the old tub and place the brand-new tub, the task is much harder. In either instance, the job is within a house handyman's skills, although you will need an assistant to move out the old tub and also set in the new one. See to it you have actually certified on your own for the work and also are comfortable attempting it. Rather than employing a contractor to take over a halfway-completed project, it is much better to think about using one prior to you begin. Chances are you might need a specialist plumber to make tube connections.
This write-up will certainly help you mount a new bath tub in your bathroom if you have currently bought a brand-new bathtub as well as do not require to change the plan of your previous supply of water pipelines.
Your devices and material checklist need to consist of the following:
Planning for the Setup
Firstly, the sustaining frame supplied with the bathroom should be fitted (if required) according to the producer's directions. Next off, fit the faucets or mixer to the bath tub. When fitting the tap block, it is necessary to ensure that if the tap includes a plastic washing machine, it is fitted between the bath and also the taps. On a plastic bath, it is also reasonable to fit a sustaining plate under the taps system to stop strain on the bathtub.
Fit the versatile faucet connectors to the bottom of the two faucets making use of 2 nuts and also olives (in some cases supplied with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet hole, and after that pass the electrical outlet with the hole in the bath. Use the nut provided by the maker to fit the plug-hole. Take a look at the plug-hole outlet for an inlet on the side for the overflow pipe.
Next off, fit completion of the flexible overflow pipeline to the overflow outlet. Afterwards, screw the pipe to the overflow face which need to be fitted inside the bath. Make sure you make use of all of the supplied washing machines.
Connect the trap to the bottom of the waste outlet on the bathtub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, as well as screw on the trap to the electrical outlet. Connect all-time low of the overflow tube in a similar manner.The bathroom should now be ready to be fitted in its last placement.
Removing Old Touches
If you require to change old taps with brand-new ones as a part of your installation, after that the first thing you need to do is separate the water system. After doing so, switch on the taps to drain pipes any type of water remaining in the system. The process of removing the existing faucets can be quite troublesome as a result of the limited access that is typically the instance.
Make use of a basin wrench (crowsfoot spanner) or a faucet tool to undo the nut that connects the supply pipelines to the taps. Have a cloth prepared for the remaining water that will certainly come from the pipelines. Once the supply pipelines have actually been gotten rid of, make use of the very same tool to loosen up the nut that holds the taps onto the bath/basin. You will require to stop the single taps from transforming throughout this procedure. As soon as the taps have been removed, the holes in the bath/basin will need to be cleaned of any type of old sealing substance.
Prior to carrying on to fit the new taps, contrast the pipe connections on the old taps to the brand-new taps. If the old faucets are longer than the new taps, then a shank adapter is needed for the brand-new faucets to fit.
Mounting the Bath tub
Utilizing the two wood boards under its feet, put the tub in the needed placement. The wood boards are handy in evenly spreading the weight of the bath tub over the area of the boards as opposed to focusing all the weight onto 4 small points.
The next goal is to guarantee that the bath tub is leveled all round. This can be attained by examining the spirit level as well as changing the feet on the bathtub till the level reads degree.
To install faucets, fit all-time low of the outermost adaptable faucet adapter to the proper supply pipe by making a compression join; after that do the same for the other faucet.
Turn on the water and also examine all joints as well as new pipework for leaks as well as tighten them if essential. Fill the tub and likewise check the overflow outlet as well as the regular outlet for leaks.
Finally, take care of the bath paneling as defined in the producer's user's manual. Tiling and securing around the bathtub should wait till the tub has been made use of at least once as this will certainly settle it into its final position.
Fitting New Taps
If the tails of the new faucets are plastic, after that you will need a plastic port to stop damage to the thread. One end of the connector fits on the plastic tail of the tap as well as the various other end gives a link to the current supply pipelines.
If you require to fit a monobloc, after that you will certainly need lowering couplers, which attaches the 10mm pipeline of the monobloc to the standard 15mm supply pipeline.
Next off, place the tap in the mounting hole in the bath/basin ensuring that the washing machines remain in location between the faucet and the sink. Protect the tap in place with the manufacturer offered backnut. As soon as the tap is firmly in position, the supply pipes can be linked to the tails of the faucets. The faucets can either be linked by utilizing corrugated copper piping or with normal faucet ports. The previous kind needs to be attached to the faucet finishes initially, tightening up only by hand. The supply pipes can later on be attached to the various other end. Tighten both ends with a spanner after both ends have been linked.
Tiling Around the Bath tub
In the area where the bath satisfies the floor tile, it is required to seal the joins with a silicone rubber caulking. This is important as the fitting can move enough to crack a rigid seal, causing the water to penetrate the wall between the bath and also the tiling, leading to complications with wetness and also possible leaks to the ceiling below.
You can select from a selection of coloured sealers to blend in your fixtures and also installations. They are offered in tubes as well as cartridges, and also are capable of securing spaces as much as a width of 3mm (1/8 inch). If you have a bigger void to fill, you can fill it with spins of soaked paper or soft rope. Keep in mind to always fill the tub with water before sealing, to permit the motion experienced when the bathtub is in use. The sealer can break relatively very early if you do not take into consideration this movement before securing.
Additionally, ceramic coving or quadrant tiles can be utilized to border the bath or shower tray. Plastic strips of coving, which are easy to use as well as reduce to size, are likewise conveniently available on the market. It is advisable to fit the ceramic tiles using waterproof or water resistant sticky as well as cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
Hopefully you liked our post on Tools You Need to Install a New Bathtub . Thanks for finding the time to read our piece. Appreciated our content? Please share it. Help someone else locate it. We recognize the value of reading our article about A Step-by-Step Guide to Installing a Bathtub.
24/7 service for plumbing emergencies. Report this page